WirelessHART Fieldgate SWG70 Instructions d'exploitation Page 23
- Page / 124
- Table des matières
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
WirelessHART Fieldgate SWG70 5 Electrical Installation
Endress+Hauser 21
5.2 Connecting to power supply and grounding
There are two 24 VDC power supply terminal blocks located inside Fieldgate SWG70, allowing for
redundant power supply. Open the housing cover to access the terminal blocks.
NOTE!
• Tension relief and bending radii: Ensure sufficient relief of tension on the cables during
installation and note the minimum bending radii of the cables.
Fig. 5-2: Power supply
Connecting to 24 VDC
power supply and
grounding
Fieldgate SWG70 must be connected to a 24 VDC (20 VDC – 30 VDC) power supply
1 Connect the grounding terminal to a ground wire.
2 Unscrew the 4 screws of the housing cover (see Fig. 4-5 in Chapter 4.2) and remove the
housing cover.
3 Route the 24 VDC power cable through the second cable gland from right
– The permissible cable diameter lies between 6 mm and 10 mm.
4 Connect the 24 VDC power cable to the first power supply connection "Line 1" observing
polarity (see Fig. 5-1 above).
5 If you want to connect a redundant power supply (optional), route the second 24 VDC power
cable through the cable gland on the far right of the housing.
6 Connect the second power cable to the second power supply connection "Line 2"
observing polarity .
7 Switch on the power: the green power LED should light immediately.
8 Tighten the cable gland with appropriate torque, see Chapter 5.5.
9 Switch off the power before making any more connections.
1 First power supply connection 3 Grounding terminals
2 Second (redundant) power supply
connection
1
2
KL14
KL15 KL16
KL17
+24V +24V0V 0V
LINE1
LINE2
+24V +24V0V 0V
LINE1 LINE2
A
B
SHD
RS485
T1
T2
RX–
RX+
TX–
TX+
ON
OFF
SHD
A
B
SHD
RS485
ETHERNET
3 3
- WirelessHART Fieldgate SWG70 1
- Table of Contents 3
- Revision History 5
- Registered Trademarks 5
- 1.1 Designated use 6
- 1.3 Operational safety 6
- 1.7 Conventions and icons 8
- 2 Identification 9
- 2.2 Device designation 10
- 2.3 Licensing agreement 10
- 3 Function and System Design 11
- 3.2 WirelessHART network 12
- 3.3.1 Instrument List 13
- 3.3.2 Cache 14
- 4 Mechanical Installation 15
- 4.1.3 Antenna characteristics 16
- 4.1.4 Antenna range 17
- 16 Endress+Hauser 18
- ≤ 20 dBi 19
- 4.3 Mounting the Fieldgate 21
- 5 Electrical Installation 22
- +24V +24V0V 0V 23
- 5.3 Connecting to Ethernet 24
- 5.4 Connecting to RS-485 25
- Plastic 2.5 Nm 26
- Nickel-plated brass 4.1 Nm 26
- Stainless steel 4.1 Nm 26
- 6Operation 27
- 6.1.1 LEDs 28
- 6.1.2 Buttons 29
- 6.1.3 DIP switches 30
- 7 Commissioning 31
- 7.2 Ethernet connection 32
- 7.2.2 Check the connection 33
- 7.3 RS-485 connection 34
- 7.4 Installing FieldCare 35
- 7.5.1 Add the HART IP CommDTM 37
- 7.5.2 Add the Fieldgate SWG70 38
- 7.6 User interface 42
- 8 Fieldgate Configuration 43
- 8.2 Wireless Communication 44
- 8.2.2 Advanced Setup 46
- 8.2.3 Operating Modes 47
- 8.3 Wired Communication 48
- 8.3.2 Ethernet 49
- 8.3.3 HART 50
- 8.3.4 Modbus 51
- 8.3.5 AMS 52
- 9 Diagnostics 53
- 9.2 Wireless Communication 54
- 9.2.2 Details 55
- 9.2.3 Burst Lists 56
- 56 Endress+Hauser 58
- Topology parameters 58
- 9.3 Wired Communication 59
- 9.3.2 HART 60
- Endress+Hauser 59 61
- HART parameters 61
- 10 Engineering 62
- 10.2 Modbus Mapping 65
- 10.2.2 Input Status 66
- Endress+Hauser 65 67
- Input Status parameters 67
- value in the Register field 69
- 10.2.3 Input Register 70
- Endress+Hauser 69 71
- Input Register parameters 71
- 11 Additional Functions 77
- 11.3 About 78
- 11.6 Set DTM Addresses (DTM) 79
- 12 Measurement 82
- 13 Maintenance and Repair 83
- 14 Trouble-Shooting 84
- 14.1.3 Expand the Network 85
- 14.2 Diagnosis 86
- Endress+Hauser 85 87
- 15 Technical Data 88
- 15.3 Power Supply 89
- 15.4 Environment 89
- 15.5 Mechanical Construction 90
- 15.6 Operability 91
- A Appendix: Modbus Interface 92
- A.1.2 Modbus in Fieldgate 93
- A.1.3 Data types 95
- A.2 Rules for mapping 96
- A.3 Mapping formats 98
- A.3.4 Read Discrete Inputs 100
- B Appendix: CSV File Formats 101
- B.3 Instrument List CSV files 102
- B.4 Topology View CSV file 102
- B.5 Details 103
- C.1 HART OPC server 104
- Endress+Hauser 105 107
- C.3.1 Fieldgate properties 108
- C.3.2 Adapter properties 109
- C.3.3 Device properties 110
- C.3.4 Device data 115
- C.4 OPC client 116
- Endress+Hauser 115 117
- D Appendix: ANATEL Approval 118
- Endress+Hauser 117 119
- For your notes 119
- 118 Endress+Hauser 120
- Endress+Hauser 119 121
© 2020, manymanuals.fr. Tous droits réservés | 0.131 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels