WirelessHART Fieldgate SWG70 Instructions d'exploitation Page 77
- Page / 124
- Table des matières
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
WirelessHART Fieldgate SWG70 11 Additional Functions
Endress+Hauser 75
11 Additional Functions
Additional Functions contains a number of functions which maybe required during the Fieldgate
life-cycle but not for everyday operation. The functions offered depend upon the parametrization
tool. In FieldCare the corresponding function is called by right-clicking on the Fieldgate SWG70
node and selecting Additional Functions.
11.1 Reset
Reset allows the Fieldgate, the instrument list and the network to be reset, see table. The reset is
intiated by pressing the appropriate button. During reset, communication with the network will be
temporarily lost.
1 Click on the Additional Functions> Reset leaf to open the dialogue:
– The significance of the parameters is described in the table below
Reset options
11.2 Self Test
Self test invokes a self testing procedure for Fieldgate SWG70.
1 Click on the Additional Functions> Self Test leaf to open the dialogue:
2 Press the Perform Self Test button to start the test
3 The results can be seen in the first two sections of the HART diagnosis dialogue:
Diagnostics =>Wired Communication =>HART dialog, Chapter 9.3.2
Parameter group Meaning
Device Reset Press this button to restart Fieldgate without any impact on the established network.
– Fieldgate SWG70 is restarted with all user settings intact
Rebuild Instrument List Press this button to regenerate the instrument list
– Create a backup of the existing instrument list before resetting, see Chapter 8.6.8
– The existing instrument list is overwritten.
– The Modbus addresses of the devices in the network may change
Reform Network Press this button to restart and reestablish the network.
– The existing instrument list is overwritten.
– The Modbus addresses of the devices in the network may change
– Depending on the size of the network, this process may take some minutes
Reset Diagnosis Bits Press this button to reset the diagnosis bits in Fieldgate SWG70
- WirelessHART Fieldgate SWG70 1
- Table of Contents 3
- Revision History 5
- Registered Trademarks 5
- 1.1 Designated use 6
- 1.3 Operational safety 6
- 1.7 Conventions and icons 8
- 2 Identification 9
- 2.2 Device designation 10
- 2.3 Licensing agreement 10
- 3 Function and System Design 11
- 3.2 WirelessHART network 12
- 3.3.1 Instrument List 13
- 3.3.2 Cache 14
- 4 Mechanical Installation 15
- 4.1.3 Antenna characteristics 16
- 4.1.4 Antenna range 17
- 16 Endress+Hauser 18
- ≤ 20 dBi 19
- 4.3 Mounting the Fieldgate 21
- 5 Electrical Installation 22
- +24V +24V0V 0V 23
- 5.3 Connecting to Ethernet 24
- 5.4 Connecting to RS-485 25
- Plastic 2.5 Nm 26
- Nickel-plated brass 4.1 Nm 26
- Stainless steel 4.1 Nm 26
- 6Operation 27
- 6.1.1 LEDs 28
- 6.1.2 Buttons 29
- 6.1.3 DIP switches 30
- 7 Commissioning 31
- 7.2 Ethernet connection 32
- 7.2.2 Check the connection 33
- 7.3 RS-485 connection 34
- 7.4 Installing FieldCare 35
- 7.5.1 Add the HART IP CommDTM 37
- 7.5.2 Add the Fieldgate SWG70 38
- 7.6 User interface 42
- 8 Fieldgate Configuration 43
- 8.2 Wireless Communication 44
- 8.2.2 Advanced Setup 46
- 8.2.3 Operating Modes 47
- 8.3 Wired Communication 48
- 8.3.2 Ethernet 49
- 8.3.3 HART 50
- 8.3.4 Modbus 51
- 8.3.5 AMS 52
- 9 Diagnostics 53
- 9.2 Wireless Communication 54
- 9.2.2 Details 55
- 9.2.3 Burst Lists 56
- 56 Endress+Hauser 58
- Topology parameters 58
- 9.3 Wired Communication 59
- 9.3.2 HART 60
- Endress+Hauser 59 61
- HART parameters 61
- 10 Engineering 62
- 10.2 Modbus Mapping 65
- 10.2.2 Input Status 66
- Endress+Hauser 65 67
- Input Status parameters 67
- value in the Register field 69
- 10.2.3 Input Register 70
- Endress+Hauser 69 71
- Input Register parameters 71
- 11 Additional Functions 77
- 11.3 About 78
- 11.6 Set DTM Addresses (DTM) 79
- 12 Measurement 82
- 13 Maintenance and Repair 83
- 14 Trouble-Shooting 84
- 14.1.3 Expand the Network 85
- 14.2 Diagnosis 86
- Endress+Hauser 85 87
- 15 Technical Data 88
- 15.3 Power Supply 89
- 15.4 Environment 89
- 15.5 Mechanical Construction 90
- 15.6 Operability 91
- A Appendix: Modbus Interface 92
- A.1.2 Modbus in Fieldgate 93
- A.1.3 Data types 95
- A.2 Rules for mapping 96
- A.3 Mapping formats 98
- A.3.4 Read Discrete Inputs 100
- B Appendix: CSV File Formats 101
- B.3 Instrument List CSV files 102
- B.4 Topology View CSV file 102
- B.5 Details 103
- C.1 HART OPC server 104
- Endress+Hauser 105 107
- C.3.1 Fieldgate properties 108
- C.3.2 Adapter properties 109
- C.3.3 Device properties 110
- C.3.4 Device data 115
- C.4 OPC client 116
- Endress+Hauser 115 117
- D Appendix: ANATEL Approval 118
- Endress+Hauser 117 119
- For your notes 119
- 118 Endress+Hauser 120
- Endress+Hauser 119 121
© 2020, manymanuals.fr. Tous droits réservés | 1.113 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels